Plumber's Essentials: Your Key to Bathtub Installation
Plumber's Essentials: Your Key to Bathtub Installation
Blog Article
They are making several good points on A Step-by-Step Guide to Installing a Bathtub in general in the content which follows.
Setting up a bathtub isn't precisely rocket science, yet it does call for strong plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bath tub with a new one is additionally a reasonably difficult task. If the old tub is conveniently easily accessible, the project can move quickly; if you need to open a wall surface to remove the old tub and also position the new bath tub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will certainly need an assistant to leave the old bathtub and set in the brand-new one. Ensure you have certified on your own for the job and are comfortable attempting it. Rather than employing a professional to take control of a halfway-completed task, it is better to think about using one before you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will help you install a brand-new tub in your shower room if you have already bought a brand-new tub and do not need to change the setup of your previous water pipes.
Your devices as well as material list ought to consist of the following:
Preparing for the Installation
First of all, the supporting frame provided with the bathroom needs to be fitted (if called for) according to the manufacturer's guidelines. Next, fit the taps or mixer to the tub. When suitable the tap block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the bathtub.
Fit the flexible faucet ports to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you utilize all of the supplied washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to currently prepare to be suited its last position.
Removing Old Touches
If you need to change old taps with new ones as a part of your setup, after that the first thing you must do is disconnect the water supply. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather problematic due to the limited gain access to that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the staying water that will originate from the pipes. When the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any type of old sealing substance.
Before going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Using the two wooden boards under its feet, place the bath tub in the called for placement. The wood boards are helpful in evenly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four tiny points.
The following objective is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the bath tub until the level reads degree.
To mount taps, fit all-time low of the outermost adaptable tap port to the proper supply pipeline by making a compression sign up with; after that do the same for the various other faucet.
Activate the water and also examine all joints and also new pipework for leaks and tighten them if necessary. Load the tub and also examine the overflow electrical outlet as well as the normal electrical outlet for leaks.
Finally, deal with the bathroom paneling as defined in the supplier's instruction manual. Tiling and securing around the bathtub needs to wait up until the bath tub has been made use of a minimum of when as this will resolve it right into its last placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end supplies a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will call for lowering couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin ensuring that the washers remain in area in between the tap and also the sink. Secure the tap in position with the manufacturer supplied backnut. Once the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal faucet ports. The previous kind needs to be connected to the tap ends first, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to crack a stiff seal, triggering the water to pass through the wall surface between the bathroom and the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your fixtures as well as fittings. They are sold in tubes as well as cartridges, and can sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked paper or soft rope. Remember to always load the tub with water prior to sealing, to permit the motion experienced when the bathtub is in use. The sealer can crack rather early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily available on the market. It is suggested to fit the floor tiles utilizing water-resistant or water-proof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were shown that article on How to Install a Bathtub from a friend on our other web property. Do you know about somebody else who is truly interested in the subject? Do not hesitate to promote it. Thank you so much for taking the time to read it.
Overflow resolution available. Report this page